LENOXTools Products

The LENOX Tools 2-Inch Bi-Metal Hole Saw (model 1772779) is engineered to solve two of the most common frustrations encountered during hole drilling: slow cutting speeds and stubborn plugs stuck inside the cup. Featuring an all-in-one design with a pre-attached arbor, this hole saw is built for tradespeople, mechanics, and home DIYers who need a dependable, ready-to-use 2-inch (51mm) cutter for electrical pass-throughs, plumbing lines, desk grommets, or camper van shore power installations.

In real-world applications, the updated T3 bi-metal tooth geometry makes a noticeable difference. The sharp, reinforced teeth bite aggressively into various materials, producing clean and accurate openings without excessive chatter. Whether boring through tough hard maple table tops or punching precise circular holes into automotive sheet metal, the saw operates with controlled efficiency. Its extended height design is deep enough to cut through standard two-by framing lumber in a single pass, saving significant job-site time.

The standout feature of this hole saw is its staircase Speed Slot. Unlike traditional hole saws that feature narrow, straight cutouts where plugs become jammed tightly, LENOX incorporates a wider, tiered slot placed low on the cylinder wall. This provides multiple leverage points, allowing you to insert a flathead screwdriver and easily pry out the cut core in seconds. Additionally, the thicker wall construction noticeably increases tool longevity and helps prevent premature tooth stripping.

The only notable trade-off is the integrated arbor configuration. While convenient for quick setup, it means the arbor cannot be detached and reused with different hole saw diameters. However, for anyone who regularly needs a dedicated, heavy-duty 2-inch hole saw that cuts rapidly and ejects plugs with minimal effort, the LENOX 1772779 is an outstanding and durable choice.

Diameter: 2 Inches (51 mm)

Arbor Type: Integrated / Arbored

Material: Bi-Metal with T3 Technology

Model Number: 1772779

Compatible Materials: Wood, 2x Lumber, Hardwoods, Sheet Metal, Plastics

Key Feature: Staircase Speed Slot for rapid plug removal

The LENOX Tools 1-1/8-Inch Bi-Metal Arbored Hole Saw (Model 1772483) is an all-in-one cutting accessory designed for plumbers, electricians, carpenters, and DIY enthusiasts. Featuring a factory-attached arbor and pilot bit, this 29mm hole saw simplifies boring tasks for running pipe, routing conduit, installing locksets, or drilling through composite panels.

At the core of its cutting efficiency is LENOX's proprietary T3 technology. The enhanced tooth geometry and thin kerf profile allow this saw to penetrate metal, hardwoods, and tough plastics significantly faster than previous models. Thicker sidewalls increase structural rigidity, resisting tooth stripping and prolonging service life under high-demand use.

One of the most notable design highlights is the staircase Speed Slot. Traditional hole saws often suffer from stubborn wood plugs becoming wedged inside the cup. The stepped, low-profile slot on this saw offers multiple leverage points, enabling you to effortlessly pry out plugs using a standard flathead screwdriver while maintaining continuous chip ejection during cutting.

While the integrated arbor ensures total convenience and zero wobble, it does mean the arbor cannot be transferred to other saw diameters. Users drilling into finished wood surfaces should also consider scoring the reverse side to prevent blowout from the aggressive tooth pattern.

Overall, the LENOX 1-1/8-Inch Arbored Hole Saw delivers high cutting speeds, superior build quality, and unmatched plug removal ease. It is a reliable, professional-grade addition to any toolbox.

Diameter: 1-1/8 in (29 mm)

Cutting Material: Bi-Metal / Alloy Steel

Arbor Configuration: Integrated Arbor with Pilot Bit

Core Extraction: Staircase Speed Slot Design

Material Compatibility: Hardwood, Softwood, Sheet Metal, Plastics, Fiberglass

Model / Part Number: 1772483 (18A)

The LENOX Tools 3002424L 1-1/2-Inch Bi-Metal Speed Slot Hole Saw with T3 Technology is engineered for trade professionals and demanding DIYers who require clean, repeatable holes without premature tool wear. Whether running electrical conduit through structural framing, notching tubing for fabrication, or installing plumbing lines, this hole saw provides the cutting speed and durability required on demanding job sites.

Performance is where the LENOX 3002424L truly excels. Equipped with LENOX T3 tooth geometry, the blade cuts up to 50 percent faster than earlier generations. The optimized tooth form and thin kerf reduce cutting resistance, allowing your drill to maintain momentum through tough alloys like stainless steel and angle iron. When operated at recommended drilling speeds and paired with cutting fluid, the bi-metal teeth maintain their sharp edge across dozens of tough cuts.

The build quality is thoughtfully designed to solve common job site headaches. A common annoyance with standard hole saws is dislodging tightly wedged plugs. LENOX addresses this with its staircase Speed Slot, placing wide slots low on the cylinder with multiple stepped leverage points so you can easily pop plugs out using a standard flathead screwdriver. Additionally, the saw body is 10 percent taller than standard models, easily clearing standard two-by dimensional lumber without binding.

While users must provide their own compatible arbor and pilot drill bit, the saw itself delivers remarkable value and performance. The LENOX 3002424L represents a benchmark in bi-metal hole saw design, balancing rapid material removal, robust wall construction, and hassle-free plug extraction.

Diameter: 1-1/2-inch (38 mm)

Model Number: 3002424L

Part Number: 30024

Material: Bi-Metal with T3 Technology

Plug Removal System: Staircase Speed Slot

Primary Compatible Materials: Mild Steel, Stainless Steel, Wood, Plastic, Cast Iron

Warranty: Manufacturer Limited Lifetime Warranty

The LENOX Tools 1-1/2 Inch Bi-Metal Speed Slot Arbored Hole Saw (Model 1772729) provides reliable cutting performance for electricians, plumbers, and DIY remodelers. Built with LENOX T3 Technology, this hole saw features an optimized tooth geometry and thick bi-metal wall design that powers through dimensional lumber, composite panels, and mild steel without premature tooth wear.

In practical use, the cutting efficiency is immediately noticeable. The sharpened tooth profile bites aggressively into lumber and metal, reducing the effort needed from the user. Because this model is built 10 percent taller than standard legacy cups, it clears 2x dimensional lumber in a single cut without bottoming out or requiring awkward clearing passes.

Core plug removal, traditionally one of the most frustrating aspects of hole saw work, is resolved by the staircase Speed Slot. By positioning wide leverage slots low along the cylinder wall, users can easily wedge a flat-blade screwdriver underneath the plug and pop it out in seconds. The wide cutouts also allow sawdust and metal shavings to escape freely during operation.

To maintain peak performance, users should manage drill speed and apply steady, moderate pressure to avoid excessive friction heat on deep cuts. Overall, this LENOX hole saw offers excellent durability, fast boring capability, and practical ease of use for general construction and workshop projects.

Diameter: 1-1/2 inches (38 mm)

Model Number: 1772729 / 24A

Material: Bi-Metal construction with high-speed steel cutting edge

Arbor Type: Integrated standard arbored shank with pilot bit

Compatibility: Standard drill chucks and drill presses

Recommended Applications: Dimensional lumber, plywood, plastics, and mild steel

The LENOX 1-Inch Speed Slot Hole Saw with Arbor (model 1772481) delivers a ready-to-use cutting solution engineered for metal, wood, and plastic drilling. Designed for professionals such as electricians and plumbers as well as home workshop users, this tool eliminates the hassle of separate arbor assembly by integrating the mount directly onto the cutting cup.

Performance is driven by an aggressive tooth geometry and reinforced cylinder walls. The enlarged, precision-sharpened teeth bite quickly into sheet metal and thick timber, producing clean circular cutouts without bogging down standard drill motors. Compared to older designs, the increased wall thickness provides greater structural rigidity, effectively preventing tooth shear and wall distortion during high-torque applications.

One of the most practical innovations is the staircase SPEED SLOT. Traditional hole saws often leave cores tightly wedged inside the cup, requiring extensive prying. The multi-tiered slot design on this LENOX unit allows users to leverage a flathead screwdriver along multiple leverage points to pop out wood and metal slugs in seconds.

While the integrated arbor provides out-of-the-box convenience, it does mean the arbor cannot be shared with other hole saw diameters in your kit. Additionally, users drilling through heavy-gauge steel should use cutting fluid to maximize tooth sharpness. Overall, this 1-inch hole saw is an exceptional, durable accessory that reliably streamlines conduit and rough-in drilling tasks.

The 1-inch diameter is tailored for electrical conduit pass-throughs, custom cable management grommets, and small pipe rough-ins across residential and commercial jobsites.

It cuts reliably through sheet metal, mild steel, aluminum, hardwood, plywood, drywall, and plastic PVC piping.